RS232 naar RS422/RS485 geïsoleerde omvormer, K3-ADE
De K3-ADE en K3-ADE-TB zijn in-line RS232 naar RS422/RS485 geïsoleerde omvormers voor 1200-38400 baud. Ze worden gevoed via de DTR- en/of RTS-signalen van de RS232 sub-D9-poort of extern. Aan de RS422/RS485 zijde bevindt zich een sub-D9 of schroefklemmenblok aansluiting. De K3-ADE bevat een microprocessor die de 2-draads RS485 half-duplex driver inlaat schakelen tussen zenden en ontvangen.
Product varianten
Artikelnummer | Productnaam | |
---|---|---|
1111-03-1103-00 + | K3 | + Vraag offerte aan |
RS232<>RS422/485 isolated coverter 9/9 pole sub-D | ||
1111-03-1103-01 + | K3-TB | + Vraag offerte aan |
RS232<>RS422/485 isolated coverter 9 pole sub-D/TB Connector |
Beschrijving
The K3-ADE is a general purpose RS232 to RS422 or RS485 isolated converter which contains a microprocessor which enables and disables the RS485 driver according to the presence of RS232 data. The K3-ADE is intended for 2-wire RS485 applications. It is also suitable for 4-wire RS485 applications where the K3-ADE is on the Slave device.
The ADE function can be disabled, to operate as the K3-TB RS232 to RS422 converter. The K3-ADE has a DB9 female connector at both ends.
Do not confuse the K3-ADE with imitations which claim to be self-powered but which in fact require power to be supplied to both sides of the converter, or which require about 40mA - far too much for any PC interface to supply.
- Automatic RS485 driver enable (ADE)
- Isolation 100% tested at >1000V AC
- RS232 port-powered in most applications
- 1200-38400 baud
- Very low supply current
- RS232 output swings above and below ground
The K3-ADE-TB is a general purpose RS232 to RS422 or RS485 isolated converter which contains a microprocessor which enables and disables the RS485 driver according to the presence of RS232 data. The K3-ADE-TB is intended for 2-wire RS485 applications. It is also suitable for 4-wire RS485 applications where the K3-ADE-TB is on the Slave device.
The ADE function can be disabled, to operate as the K3-TB RS232 to RS422 converter. The K3-ADE-TB has a DB9 female connector on the RS232 port and a removable 5-way terminal block on the RS422 or RS485 port
Do not confuse the K3-ADE-TB with imitations which claim to be self-powered but which in fact require power to be supplied to both sides of the converter, or which require about 40mA - far too much for any PC interface to supply.
- Automatic RS485 driver enable (ADE)
- Isolation 100% tested at >1000V AC
- RS232 port-powered in most applications
- 1200-38400 baud
- Very low supply current
- RS232 output swings above and below ground
Specificaties
- Serial parameters:
- 0-38400 baud, any character format including break levels
- RS232 interface:
- RX threshold +1,5V typ.
- RS422/RS485 interface:
- RX threshold 200mV typ. (defferential), Max. common-mode voltage -7V to +12V
- Supply current:
- 4,5mA all baud rates
- Supply voltage:
- RTS & DTR RS232 port or +6 to +16VDC on pin 9
- Isolation:
- 1500V RMS
- RS232 connector:
- Sub-D 9 pole female
- RS422/RS485 connector:
- K3: Sub-D 9 pole female • Screw terminal block
- CE compliance:
- Emissions EN50081-2, imminity EN50082-2
- Operating temperature:
- 0°C to +50°C, RH 0 to 90% non-condensing
- Dimension:
- 50mm (w) x 20mm (h) x 80mm (l)